Filabot EX2 Extruder Setup
Filabot EX2 Extruder Setup enables you to profit from evolution in plastic recycling and make clever use of industrial plastics. In essence, it is a small-scale solution to a big environmental problem making sustainable manufacturing possible for a larger audience, not only those with expert knowledge. This closed loop system is an example of sophisticated engineering - our specialists managed to downsize an entire filament production line into three elements: Filabot Extruder, Filabot Airpath, and Filabot Spooler. This bundle is a full setup that includes everything that is needed to develop and produce filament for any FDM or FFF 3D printer.
Filabot EX2 Extruder
The Filabot EX2 system is our entry-level extrusion system, designed to be simple for those who are just starting to make filament. The EX2 features a compact three-stage extrusion screw made from hardened and polished high-carbon stainless steel. This proprietary, patent-pending screw is designed to pressurize plastic during the extrusion process, assisting in diameter control and boosting the overall output. The mixing capability of the screw is enhanced by the utilization of a progressive compression section, which applies shear force between the polymer and the barrel wall. The EX2 also features extrusion speed control. The speed control board includes an automatic, variable voltage control module that is engineered to regulate the precise RPM of the screw as forces fluctuate in the extrusion process. When used with the Filabot Spooler, tolerances of +/-0.05mm can be achieved at a rate of 2 lbs an hour.
Filabot Airpath
The Filabot Airpath uses forced convection to cool filament as it is being extruded. The Filabot Spooler can be used for the common ABS and PLA materials to help get greater tolerance and easier extrusion setup. The air path is a must for researchers and development labs who are working with higher temperature polymers where the filament needs to be cooled before it is passed through the Filabot Spooler. This system has a speed readout so that consistent speeds can be set.
Filabot Spooler
The Filabot Spooler is the ultimate compliment to our extruder systems. In addition to conveniently spooling your extruded filament, the unit allows you to easily fine-tune the extrusion diameter for the tightest possible tolerances. This is achieved by adjusting the speed of the puller wheels, which draw the filament from the extruder. The puller wheels have been engineered to be non-compressive, meaning they preserve the quality of the extrusion. This updated model features a variable traverse mechanism to evenly distribute filament onto the spool, an upgraded circuit board for the smoothest possible power delivery, and stainless roller shafts which glide on sealed bearings.
Bundle Includes
Filabot EX2
Filabot Airpath
Filabot Spooler
EX2 Includes
1. 2.85mm Nozzle
1. 1.75mm Nozzle
1. User Manual
1. Power Cord
1. Packet of Anti-Seize
1. Package of Purge
Typical measured power consumption, which will vary, for different polymers it's 190 Watts for the EX2 Bundle.
Extrudable Plastics: ABS, ABS Flame Retardant, 4043D PLA, 3D850 PLA, 3D870 PLA, PC, HIPS, PETG, and WAX. Lower Melt Flow Polymers
Extrusion Rate: Over 2 lbs (0.91kg) of filament per hour (About 250 inches per minute using 4043D PLA @ 1.75mm)
Filament Sizes: 1.75mm and 2.85mm Material Input Size: 1/8in (3.18mm) pellets to powder.
Material Capacity: Hopper Volume - approximately 26 cubic inches (426.1 cubic cm)
Screw Void - 1.75 cubic inches (28.8 cubic cm)
Temperature Control: PID Controller, One Zone
Feed Screw and Drive: 0-35rpm Speed Control 85in lbs (9.6 Nm) drive force General Purpose Custom Designed Feed Screw Non- Removable Screw Dimensions: OD: 5/8" L/D ratio: 12 Pitch: 1/2" Compression: 2.5:1
Universal Power Input (For the EX2): 110 VAC or 220 VAC - 50 to 60hz - 500 watts
Physical Characteristics: Weight 28 lbs (12.7kg) and dimensions of 18in x 7in x 9in (45.75cm x 17.78cm x 22.86cm)
Full 1 Year Warranty
**Voltage Note - the 110VAC or 220VAC specific to the country that you are going to be using the extruder system in. There is no operational difference between the 110VAC or 220VAC.**